DATA COMMUNICATION NETWORKING
DATA COMMUNICATION NETWORKING
In its simplest form, data communication takes place between two devices that are directly connected by some form of point-to-point transmission medium. Often, however, it is impractical for two devices to be directly, point-to-point connected. This is so for one (or both) of the following contingencies:
- The devices are very far apart. It would be inordinately expensive, for example, to string a dedicated link between two devices thousands of miles apart.
- There is a set of devices, each of which may require a link to many of the others at various times. Examples are all of the telephones in the world and all of the terminals and computers owned by a single organization. Except for the case of a very few devices, it is impractical to provide a dedicated wire between each pair of devices.
The solution to this problem is to attach each device to a communications network. The two major categories into which communications networks are traditionally classified:
- wide-area networks (WANs) and
- local-area networks (LANs).
Wide-Area Networks
Wide-area networks have been traditionally been considered to be those that cover a large geographical area, require the crossing of public right-of-ways, and rely at least in part on circuits provided by a common carrier. Typically, a WAN consists of a number of interconnected switching nodes. A transmission from any one device is routed through these internal nodes to the specified destination device. These nodes (including the boundary nodes) are not concerned with the content of the data; rather, their purpose is to provide a switching facility that will move the data from node to node until they reach their destination. Traditionally, WANs have been implemented using one of two technologies:
- circuit switching and
- packet switching.
Circuit Switching
In a circuit-switched network, a dedicated communications path is established between two stations through the nodes of the network. That path is a connected sequence of physical links between nodes. On each link, a logical channel is dedicated to the connection. Data generated by the source station are transmitted along the dedicated path as rapidly as possible. At each node, incoming data are routed or switched to the appropriate outgoing channel without delay. The most common example of circuit switching is the telephone network.
Packet Switching
A quite different approach is used in a packet-switched network. In this case, it is not necessary to dedicate transmission capacity along a path through the network. Rather, data are sent out in a sequence of small chunks, called packets. Each packet is passed through the network from node to node along some path leading from source to destination. At each node, the entire packet is received, stored briefly, and then transmitted to the next node. Packet-switched networks are commonly used for terminal-to-computer and computer-to-computer communications.
Frame Relay
Packet switching was developed at a time when digital long-distance transmission facilities exhibited a relatively high error rate compared to today's facilities. As a result, there is a considerable amount of overhead built into packet-switched schemes to compensate for errors. The overhead includes additional bits added to each packet to introduce redundancy and additional processing at the end stations and the intermediate switching nodes to detect and recover from errors. With modern high-speed telecommunications systems, this overhead is unnecessary and counterproductive. It is unnecessary because the rate of errors has been dramatically lowered and any remaining errors can easily be caught in the end systems by logic that operates above the level of the packet-switching logic; it is counterproductive because the overhead involved soaks up a significant fraction of the high capacity provided by the network.
Frame relay was developed to take advantage of these high data rates and low error rates. Whereas the original packet-switching networks were designed with a data rate to the end user of about 64 kbps, frame relay networks are designed to operate efficiently at user data rates of up to 2 Mbps. The key to achieving these high data rates is to strip out most of the overhead involved with error control.
ATM
Asynchronous transfer mode (ATM), sometimes referred to as cell relay, is a culmination of all of the developments in circuit switching and packet switching over the past 25 years. ATM can be viewed as an evolution from frame relay. The most obvious difference between frame relay and ATM is that frame relay uses variable-length packets, called frames, and ATM uses fixed-length packets, called cells. As with frame relay, ATM provides little overhead for error control, depending on the inherent reliability of the transmission system and on higher layers of logic in the end systems to catch and correct errors. By using a fixed-packet length, the processingoverhead is reduced even further for ATM compared to frame relay. The result is that ATM is designed to work in the range of 10s and 100s of Mbps, compared to the 2-Mbps target of frame relay.
ATM can also be viewed as an evolution from circuit switching. With circuitswitching, only fixed-data-rate circuits are available to the end system. ATM allows the definition of multiple virtual channels with data rates that are dynamically defined at the time the virtual channel is created. By using full, fixed-size cells, ATM is so efficient that it can offer a constant-data-rate channel even though it is using a packet-switching technique. Thus, ATM extends circuit switching to allow multiple channels with the data rate on each channel dynamically set on demand.
ISDN and Broadband ISDN
Merging and evolving communications and computing technologies, coupled with increasing demands for efficient and timely collection, processing, and dissemination of information, are leading to the development of integrated systems that transmit and process all types of data. A significant outgrowth of these trends is the integrated services digital network (ISDN). The ISDN is intended to be a worldwide public telecommunications network to replace existing public telecommunications networks and deliver a wide variety of services. The ISDN is defined by the standardization of user interfaces and implemented as a set of digital switches and paths supporting a broad range of traffic types and providing value-added processing services. In practice, there are multiple networks, implemented within national boundaries, but, from the user's point of view, there is intended to be a single, uniformly accessible, worldwide network.
Despite the fact that ISDN has yet to achieve the universal deployment hoped for, it is already in its second generation. The first generation, sometimes referred to as narrowband ISDN, is based on the use of a 64-kbps channel as the basic unit of switching and has a circuit-switching orientation. The major technical contribution of the narrowband ISDN effort has been frame relay. The second generation, referred to as broadband ISDN, supports very high data rates (100s of Mbps) and has a packet-switching orientation. The major technical contribution of the broadband ISDN effort has been asynchronous transfer mode (ATM), also known as cell
relay.
Local Area Networks
As with wide-area networks, a local-area network is a communications network that interconnects a variety of devices and provides a means for information exchange among those devices. There are several key distinctions between LANs and WANs:
- The scope of the LAN is small, typically a single building or a cluster of buildings. This difference in geographic scope leads to different technical solutions, as we shall see.
- It is usually the case that the LAN is owned by the same organization that owns the attached devices. For WANs, this is less often the case, or at least a significant fraction of the network assets are not owned. This has two implications. First, care must be taken in the choice of LAN, as there may be a substantial capital investment (compared to dial-up or leased charges for widearea networks) for both purchase and maintenance. Second, the network management responsibility for a local network falls solely on the user.
3. The internal data rates of LANs are typically much greater than those of widearea
networks.
Traditionally, LANs make use of a broadcast network approach rather than a switching approach. With a broadcast communication network, there are no intermediate switching nodes. At each station, there is a transmitterlreceiver that communicates over a medium shared by other stations. A transmission from any one station is broadcast to and received by all other stations. A simple example of this is a CB radio system, in which all users tuned to the same channel may communicate. We will be concerned with networks used to link computers, workstations, and
other digital devices. In the latter case, data are usually transmitted in packets. Because the medium is shared, only one station at a time can transmit a packet.
Like it on Facebook, Tweet it or share this article on other bookmarking websites.